Sell FORD VISE

Sell FORD VISE	Total 20 Related Items Prev Next


Date Posted :	2009/07/02

Category :	Automobiles & Motorcycles > Car Care Products

Offer Type :	Sell

View Larger Picture

Autosky Science and Technology Co., Ltd.

Membership Type : Free member
Registration Date : 2008-10-07
Country/Region :

China
Address : Cell2, Yunmei Yuan, Meihua Shanzhuang, Minzhi Village, Longhua Twon, Baoan district, Shenzhen Shenzhen Guangdong, China
Phone : 86-0755-29806915
Fax : 86-0755-null
Contact : Sara He

View all selling leads of this member(20)
View all products of this member (14)

Check this company's business credentials, background and level of reliability

This machine can copy the ford key without key in hand ,it only need the code of key

For Ford Key Copy Vise Manual Instruction:

I. Standard Appendix
1.One pc of pitch positioning base.
2.One pc of angle locking base.
3.One pc cutter and tracer each.
4.One 2mm Six-hexagon wrench.

II. Vise sketch map
III. Key Copy Vise Manual Instruction:
1. Angle Locking Base
There are right and left - two directions and four different depths in Ford key system.
2. Pitch Positioning Base
There are six different pitches a징짖c징짖e in one side and b징짖d징짖f in another side. The cutting position can be changed by turning the Pitch Turning Knob.

IV. Skill of adjusting the depth of cutter and tracer.
1. Put the attached cutter and tracer on the machine(tip of tracer should be 5mm lower than tip of cutter at least), use 2mm Hexagon Wrench to loosen key fixing screw of angle locking base, insert blank key in and lock it, then set these two bases on the vise of machine.
2. Power on the motor, press down the handle of cutter fully, turn the depth adjusting knob to make the tip of tracer higher & cutter can touch the surface of key lightly, then, lock the depth fixing knob of machine to set up this depth, and then turn machine's depth adjusting knob of tracer again for half circle counterclockwise to lift up the tracer more higher and lock the tracer locking knob (to eliminate the spring the tracer, make it unable to move up and down). Then the adjusting work is finished.

V. Skill of copy Keys
1.Identify each angle of original key.
2.Write down the pitches' no. (from the tip of Ford Key) & depths' codes accordingly in order like pitch no.1(f) = angle code 2, pitch no.2(e) = angle code 3....etc.
3.Put the key blank into angle locking base, after locking key fixing screw, follow the following steps to copy keys:

Related Keywords: FORD VISE, auto maintenance, auto repair tools, auto key programmer

Other Selling Leads of this member (19 more)

Sell NEC programmer

COM connector and support USB connector as well, Mileage correction 쨘C reset your the mileage by directly input the data; Works on CPUs use NEC board, support userself upgration. Applicable models ��Citroen Xsara Picasso( NEC MCU in BSI ) �...

Sell X-PROG-M

Supported Device: Serial Eprom: 24Cxx, 25Cxx, 93Cxx, MDA2062, NVM3060, M6M800xx, S2100, S24Hxx, TC89xxx, X2444, M35080 TEXAS INSTRUMENTS TMS370 Series: TMS370C002A, TMS370C010A, TMS370C012A, TMS370C020A, TMS370C022A, TMS370C032A, TMS370C036A...

Sell X-PROG

The XPROG supports programming of Motorola 68HC05xx, 68HC08xx, 68HC11xx microcontrollers internal EEPROM and serial EEPROM's - most used programmable device in car radios,automotive computers (dashboards, AIRBAG, immobilizers), and industrial product...