Sell VAG Tacho USB 2.5 + Opel Immo Pin Code Reader

Sell VAG Tacho USB 2.5 + Opel Immo Pin Code Reader	Total 48 Related Items Prev Next


Date Posted :	2009/07/17

Category :	Automobiles & Motorcycles > Car Care Products

Offer Type :	Sell

View Larger Picture

UUC Technology Co.,LTD

Membership Type : Free member
Registration Date : 2009-05-14
Country/Region :

China
Address : No.158 Huafu Road Shenzhen Guangdong, China
Phone : 86-0755-89517839
Fax : 86-0755-89969396
Contact : Lily Zhang

View all buying leads of this member(1)
View all selling leads of this member(48)
View all products of this member (15)

Check this company's business credentials, background and level of reliability

This cable is both for VAG and Opel, when it is connected to the VAG TACHO USB 2.5 software, it works as VAG TACHO USB cable, when it is connected to Opel Immo Pin code Reader, it works as Pin code reader.
1. For VAG:
Bosch/Motometer dashes for VW 2001-2003 years V07.04, V07.05, V07.08, V07.13 (with scan for 2'nd pass)
Audi A4,A6,A8 separate immo box 1994-1999 read PIN code,and read/write eeprom!
Audi A3,A4,A6,TT, New Beetle Magnetti Marelli M73 (1998-2003 year) read PIN code / change mileage!
New Beetle Magnetti Marelli M73 (2001 to 2005 year) read PIN code Almost all VDO dashes for VW/Seat/Skoda up to year 2004 read/write eeprom!
Almost all VDO dashes for Audi up to year 2001 read/write eeprom!
Almost all MotoMeter dashes for VW/Seat up to year 2001 read/write eeprom!
Automatic functions: Change mileage, Read PIN code !
All this by using car OBD connector!
Without disassembly dash or immo box from car!
User can save and read files to / from program memory buffer.
Connect Any Tacho button
Connect Selected ECU
Read Info
Read PIN
Change Mileage
Stop Action
Read eeprom
Program New Key
Disconnect
View memory buffer
Write eeprom
Clear ECU errors
2. For Opel:
Immo1 & Immo2 supported up to year 2004
Manual for programming new keys.
User can program up to 5 diferent keys to an immobiliser.

How to do this:
Insert new key, and switch ignition ON.
Connect to immobilizer.
Enter correct PIN code.
Press "Prog New Key " Message 'Reading key...' will be displayed on screen.
After successful procedure there will be a message: 'Key programmed!' Wait 10 seconds and turn ignition OFF.
Turn ON ignition with same key, and wait until yellow indicator lamp on car dash stop flashing, and ligth on continiously.
Start the car to test new keyIf the indicator lamp continue flashing, this means that transponder is notcompatible to this car or engine ECU, try to program other tran

Related Keywords: VAG Tacho USB 2.5, Opel ImmoPin Code Reader, car tool, VAG diagnostic tool

Other Selling Leads of this member (47 more)

Sell VAG K+CAN Commander 2.5

Diagnostic via CAN and Special functions via K-line. Covers all electronic control units in vehicles (diagnostic addresses from 0x01 to 0x80). This can allow of user to investigate and diagnosis some new units untouchable for remaining diagnostic t...

Sell New CAN BUS Service and Airbag Reset

The service interval resetter New CAN BUS Service and Airbag Reset is used exclusively to reprogram the service intervals for the following vehicles: - Service interval - Place of installation onboard diagnosis socket - Resetting the service inte...

Sell SI-Reset for MB

Service Intervall Reset for Mercedes Benz cars with 38 pin connector except ML class - Resets the Service Indicator (Service Intervall) - Delete airbag faults (if your airbag warning light is on you can turn it off with this tool, if the error ...