EC21, Global B2B Marketplace
Sign In
Join Free
Buy Now
Sell Now
My EC21
Help
Search Advanced Search
Products > be. > Jingsu Liangyi Co.,Ltd | Similar Products
Your search for "

be.

" found 16 Products from Jingsu Liangyi Co.,Ltd, China
Inquire Now

(1-16 out of 16)

34CrNiMo6 / 1.6582 (AISI 4340) Ni-Cr-Mo Steel Forgings Shafts, Gears | Jiangsu Liangyi

34CrNiMo6 / 1.6582 (AISI 4340) Ni-Cr-Mo Steel Forgings Shafts, Gears | Jiangsu Liangyi
be flame/induction hardened or nitrided after Q&T. Hard to weld (softened state, preheat). Why engineers specify 34CrNiMo6 / 1.6582 As the EN 4340-grade workhorse it delivers high strength, toughness ...

A182 F61 / UNS S32550 Super Duplex Stainless Forgings Rings, Bars, Valves | Jiangsu Liangyi

A182 F61 / UNS S32550 Super Duplex Stainless Forgings Rings, Bars, Valves | Jiangsu Liangyi
be preserved by solution annealing (~1,080–1,120 °C) and rapid water quench, avoiding sigma-phase and intermetallic precipitation. Weldable with duplex-matched procedures and controlled heat ...

Alloy 20 / UNS N08020 / 2.4660 Sulfuric-Acid Stainless Forgings Rings, Bars, Valves

Alloy 20 / UNS N08020 / 2.4660 Sulfuric-Acid Stainless Forgings Rings, Bars, Valves
be hardened by heat treatment; high work-hardening rate (low cutting speeds, heavy feeds). Why engineers specify Alloy 20 / UNS N08020 / 2.4660 Six decades the standard for sulfuric-acid service: it ...

31CrMoV9 (W.Nr. 1.8519) Nitriding Steel Forging Parts EN 10085 Cr-Mo-V Bars, Rings, Gear & Rotor

31CrMoV9 (W.Nr. 1.8519) Nitriding Steel Forging Parts EN 10085 Cr-Mo-V Bars, Rings, Gear & Rotor
grade, 1.7707 the older DIN grade. • What surface hardness is achievable? Up to ~800 HV after nitriding over a tough Q&T core. • Can it be welded? No — 31CrMoV9 is not recommended for welded ...

32CrMo12 (W.Nr. 1.7361) Forging Parts EN 10250-3 Cr-Mo Alloy Steel Bars, Rings

32CrMo12 (W.Nr. 1.7361) Forging Parts EN 10250-3 Cr-Mo Alloy Steel Bars, Rings
be nitrided for a hard wear surface. Why engineers specify 32CrMo12 / 1.7361 Its deep hardenability and high fatigue strength make it the choice for heavily loaded gear and pinion shafts, riding gear ...

1.2714 (55NiCrMoV7 / AISI L6) Forging Parts Hot-Work Die Steel Bars, Blocks, Rings & Shafts

1.2714 (55NiCrMoV7 / AISI L6) Forging Parts Hot-Work Die Steel Bars, Blocks, Rings & Shafts
be normalised. Why engineers specify 1.2714 / 55NiCrMoV7 Its high toughness with hot strength and hardenability — and very little distortion after heat treatment — make it the standard for ...

31CrMo12 (W.Nr. 1.8515) Nitriding Steel Forging Parts EN 10085 Cr-Mo Bars, Rings, Gear & Extruder

31CrMo12 (W.Nr. 1.8515) Nitriding Steel Forging Parts EN 10085 Cr-Mo Bars, Rings, Gear & Extruder
/ 722M24 (not identical). • What surface hardness is achievable? Up to ~800 HV after nitriding, over a tough Q&T core. • Can it be welded? No — 31CrMo12 is not recommended for welded ...

EN26 / 826M40 (1.6745 / 40NiCrMo10-5) Forging Parts High-Tensile Bars, Rings, Crank & Gear Shafts

EN26 / 826M40 (1.6745 / 40NiCrMo10-5) Forging Parts High-Tensile Bars, Rings, Crank & Gear Shafts
be flame/induction hardened or nitrided ~490–530 °C to a surface up to ~Rc 60 with little distortion. Why engineers specify EN26 / 826M40 It delivers higher tensile and yield than 4140, 4340 or EN25 ...

1.6985 (28CrMoNiV4-9) Turbine Rotor Forging Material SEW 555 Cr-Mo-Ni-V Monobloc Rotor & Generator

1.6985 (28CrMoNiV4-9) Turbine Rotor Forging Material SEW 555 Cr-Mo-Ni-V Monobloc Rotor & Generator
— it is a specialty SEW 555 rotor steel. • How large can rotors be? HP/IP/LP monobloc rotor shafts to ~30 t, 1,800 mm diameter, 15 m length. • What testing is included? Multi-orientation ...

1.6946 (30CrMoNiV5-11) Turbine Rotor Forging Steel SEW 555 Cr-Mo-Ni-V Rotor Shafts

1.6946 (30CrMoNiV5-11) Turbine Rotor Forging Steel SEW 555 Cr-Mo-Ni-V Rotor Shafts
similar turbine-rotor grades). • How large can rotors be? Ingots up to ~50 t; monobloc rotor shafts to large sections (through-hardening best ≤~1,200 mm). • What testing is included? ...

39NiCrMo3 (W.Nr. 1.6510) Forging Parts EN 10083-3 Ni-Cr-Mo Bars, Rings, Gear & Crank Shafts

39NiCrMo3 (W.Nr. 1.6510) Forging Parts EN 10083-3 Ni-Cr-Mo Bars, Rings, Gear & Crank Shafts
be case hardened (to 53–58 HRC surface) or nitrided (surface to ~600 HV1). Hot forging 850–1,150 °C; harden 830–860 °C, oil quench; temper 550–650 °C; soft/isothermal anneal ~650 °C. As a white-spot ...

AISI 4150 (SAE 4150 / 50CrMo4) Forging Parts Alloy Steel Bars, Rings, Shafts & Gears for Mining

AISI 4150 (SAE 4150 / 50CrMo4) Forging Parts Alloy Steel Bars, Rings, Shafts & Gears for Mining
be flame/induction surface-hardened. Why engineers specify AISI 4150 / G41500 It delivers higher strength, hardness and wear resistance than 4140 while keeping deep hardenability and toughness — a ...

Inconel 783 (Alloy 783 / UNS R30783) Forged Parts AMS 5839 Rings, Flat Bars for Gas Turbines

Inconel 783 (Alloy 783 / UNS R30783) Forged Parts AMS 5839 Rings, Flat Bars for Gas Turbines
be held across thermal cycles, improving engine efficiency over higher-expansion alloys. Frequently asked questions • Is UNS R30783 the same as Alloy 783? Yes — Inconel 783, Alloy 783, UNS R30783 ...

30CrMoV9 (W.Nr. 1.7707) Nitriding Steel Forging Parts Bars, Rings, Gear & Pinion Shafts for Power

30CrMoV9 (W.Nr. 1.7707) Nitriding Steel Forging Parts Bars, Rings, Gear & Pinion Shafts for Power
are the same EN nitriding steel. • Does it have an AISI equivalent? No exact equivalent; it is a dedicated nitriding steel and is only loosely comparable to 4340-type alloy steel (not ...

PH13-8Mo (/ 1.4534,XM-13 / UNS S13800 / X3CrNiMoAl13-8-2,AMS 5629) Forging Rings,Bars,Discs

PH13-8Mo (/ 1.4534,XM-13 / UNS S13800 / X3CrNiMoAl13-8-2,AMS 5629) Forging Rings,Bars,Discs
Higher H950 strength (1517 vs 1310 MPa), much better SCC and pitting resistance and superior transverse toughness. • Which conditions are available? H950, H1000, H1025, H1050, H1100, H1150 — plus ...

Monel 400 (UNS N04400 / W.Nr. 2.4360 / Alloy 400) Forged Components ASTM B564 Bars,Ring,Shafts

Monel 400 (UNS N04400 / W.Nr. 2.4360 / Alloy 400) Forged Components ASTM B564 Bars,Ring,Shafts
be supplied to NACE MR0175 for sour service? Yes — Monel 400 is listed in NACE MR0175 / ISO 15156-3; hardness controlled ≤35 HRC, with compliance noted on the 3.1/3.2 certificate. • What is the ...
Page 1 of 11
Go to Page Go
Share :
Facebook
Twitter
LinkedIn
My Favorites
Email this page

Browse: Manufacturer Directory Premium Suppliers Site Map

About EC21 Contact Us Terms & Conditions Report Item Online Trading Risks Product Listing Policy

Copyright (c)1997-2026 EC21 Inc. All Rights Reserved. EC21 in KoreanChinese

Business Registry Number: 120-86-03931 | Mall order sales Registration Number: 강남-5838

Inquiry Basket ()