Place of origin:
China
Supply Ability:
2000tons monthly
single bars, twin bars or combination of single bars and twin bars. 4.The technical data of Low Price Reinforcing Mesh Panel is contained composition and characteristic mechanical porperties of reinforcing steels. 4.1.1 Table1 Composition of reinforcing steels Type of analysis Chemical composition, % max All grades Carbon equivalent value(Ceq)for standard grades C P S 250N 500L 500N 300E 500E Cas
[Related Keywords : Square Reinforcing Mesh, Galvanized Mesh]
Business Type
Manufacturer
Location
Hebei, China
Employees Total
101 - 500
Annual Revenue
USD 2,000,001 - 5,000,000
Min. Order:
1 Piece
Price:
US$ 21400
Place of origin:
China
Supply Ability:
100 sets per month
single and double side lapping systems. Our vitrified diamond and CBN grinding discs have high grinding efficiency, high wear resistance and abrasive consumption, good surface quality and flatness of the workpiece. Applicable Areas of double discs: ♦ Hydraulic pneumatic components. vane pump, conversion valve, piston pump, fuel pump, hydraulic motor parts ♦ Compressor spare parts. air condit
[Related Keywords : Grinding disc, Vitrified Grinding disc, Diamond Grinding disc, CBN Grinding disc]
Business Type
Manufacturer
Location
Henan, China
Employees Total
11 - 50
Annual Revenue
USD 100,000 - 500,000
Min. Order:
1 Sheet
Price:
US$ 50 ~ 999
Place of origin:
China
single-crystal silicon parts. We also accept small-lot orders for prototyping, research, and other applications. Silicon wafers for R&D and equipment testing 1.We supply high-quality wafers, including one-sided polished wafers 2 to 12 inches in diameter and wafers with oxide films. 2.Following the needs of our customers, we are able to supply rectangular and non-OF (orientation flat) (round) wafe
[Related Keywords : Silicon Prism, Silicon Target, Silicon Parts, Silicon lens]
Business Type
Manufacturer
Location
Jiangsu, China
Employees Total
51 - 100
Annual Revenue
USD 100,000 - 500,000
Place of origin:
China
Single Side Polished /Double Sides Polished Polished side Ra <0.5nm Back Side Criteria General is 0.2-0.5µm or as customized Edge Criteria R=0.2mm or Bullnose Optical doped Zn/MgO etc Wafer Surface Criteria Contamination, None Particles ￠>0.3 µ m <= 30 Scratch , Chipping None Defect No edge cracks, scratches, saw marks, stains Packaging Qty/Wafer box 25pcs per box CQT dedicated to produce se
[Related Keywords : Lithium Tantalate Wafers]
Business Type
Manufacturer
Location
Zhejiang, China
Employees Total
101 - 500
Annual Revenue
More than 100,000,000
Place of origin:
China
single surface or double surfaces covered with glue F46, and processed after drying and cutting. The tape is applicable for acting as grade H insulating material of electrical wire lapping. It takes into its shape through melting at 350-380 °C over ten minutes. CR Type: Corona resistance polyimide film without any F46 coating. FCR Type: Corona resistance polyimide film with F46 single side coati
[Related Keywords : FCR Polyimide Tape, CR Polyimide Tape, FEP Polyimide Film FHF, FCRF Polyimide Tape]
Business Type
Manufacturer
Location
Jiangsu, China
Employees Total
51 - 100
Annual Revenue
USD 2,000,001 - 5,000,000
Place of origin:
China
Supply Ability:
200 tons per month
single crystals is around 95%, which is 50% higher than the original one(the original one's is about 65%). 2.The compressive strength exceeds 26N, toughness is as much as 90.5%, which is 25% higher than original one's. 3.Al2O3 is above 99.4% and its impurity is lower than original one's. 4.With multi-layer grain, SSA can create lots of cutting sides continually. So the surface of grinded workpie
[Related Keywords : Monocrystalline Aluminum]
Business Type
Manufacturer
Location
Henan, China
Employees Total
51 - 100
Annual Revenue
USD 100,000 - 500,000
Min. Order:
100 Piece
Price:
US$ 1 ~ 100
Place of origin:
China
side the needle is blunt to avoid injurying other organs. Features & Benefits sharp tip for easy insertion visual needle position indicator high-flow stopcock with luer lock connector Insufflation Needle Insufflation Veress Needle Specification of Veress Needle Item No. B090102120/B090202150 Product Name Disposable veress needle Type 120mm/150mm Single Packing 1.2x7.5x27cm Material Medical grade
[Related Keywords : veress needle factory]
Business Type
Manufacturer
Location
Zhejiang, China
Employees Total
51 - 100
Annual Revenue
USD 1,000,001 - 2,000,000
Competitive single side lapping products from various single side lapping manufacturers and single side lapping suppliers are listed above, please select quality and cheap items for you.
 |
Recommended Content
