Battery Condition Tester (Identifier & Regenerator & Discharger)
Model : RPT-T300
Renewable Energy by Green Technology
All New HF Pulse Innovation
PRIME Battery Regenerator adopted the most innovative High-Frequency Pulse technology which is proprietary developed by the cutting-edge technology of REPOWERTEK.
SOLAR, UPS, Electricity, Telecom Tower, Military, Eco Town, Electric-Forklift, Golf cart, Wheelchair, Lift & Scrubber, Automotive Vehicle, Heavy Equipment, Agricultural Equipment, Marine Boat, Train, etc.
RPT-T300 Battery Condition Tester & Regeneration System (7-in-1 Multi-functional Regeneration System)
is a special all-in-one Battery Condition Tester for 6V~12V lead-acid batteries. It supports multi-functions of digital Regenerator + Charger + Discharger + Power Supply + IR & CCA Checkers + Battery Condition Tester up to 300Ah at 12V batteries.
A 12V battery is composed of 2 volts x 6 cells. Before a restoration process, it is hard to know about the shorted circuit, cell cut, cell corrosion state, and any damaged cells. For this reason, the other competitors must only check on these damaged
cases after finishing a process. So, we have developed on 'RPT-T300'. It can find the short of electrodes and damaged cells within a few minutes before the restoration procedure. Automatic battery condition test function (whether to be restored or
not - by 'CONDITION TEST' mode). Using it, most batteries will assort for targeting ones to be regenerated with our new RPT-T300 if they do not have any cell cut or short and internal cell damage (corrosion). RPT-T300 has a fully automated function
to regenerate by setting voltage and Total capacity only.
Functional Modes
- 1. Regenerator (6V~48V all adjustable voltages-in-one, 40Ah~ 400Ah capacity) at 'REGENERATION' mode
- 2. Charger (6V~48V all adjustable voltages-in-one, Up to 400Ah capacity) at 'CHARGE' mode
- 3. Power Supply (6V~48V free setting mode of Voltage, Current & Time for special & sleeping batteries)
* Mainly used for 2V Reach Forklift, TELECOM UPS & other Traction bank/rack connected batteries
* Mainly used for 12V bank
connected batteries up to 48V (4 x 12V batteries at the same time).
* Maximum Limited Output Current : 6V~48V = 30A
* A Discharger (RPT-D10K) is optional.
Specifications
- RPT-E400 (3-in-1) : 230mm(H) x 345mm(W) x 440mm(D), Approx. 17kg
Variable Application
- All kinds of 6V ~ 12V lead-acid batteries including VRLA & Deep Cycle
- Restoring and recharging up to 300Ah battery capacity
- Optimization of operation conditions for all countries
- Lowest power consumption using SMPS with switching control
- AC80 ~ 120V / 210 ~ 250V Compatibility
Smart Control System by Micom
- Control minute electric current & Voltage depending on the type of battery
- Restoring and recharging for small capacity (40 ~ 300Ah) batteries
- Minimizes damage to electrodes and restrain accumulation of sulfate on electrodes
- Optimized high frequency pulse with charging curve algorithm
Optimized charging and restoring algorithm
- Utilizes special pattern information on various battery kinds and characteristics
- Adopted on the optimized high-frequency Pulse
- Prevents electrical / physical damage when restoring and charging batteries
- Prolongs battery lifecycle 2~3 times
Wide Application Range
- Can regenerate and charge high-capacity batteries (Max.300Ah)
- Can discharge all of 6V ~ 12V batteries (Max. 420W)
- Can condition test all types of lead-acid 12V batteries (DC 12V only)
- Can restore and charge GEL and AGM VRLA type batteries
- Can measure Internal Resistance and CCA twice (before & after)
- Can set up values manually as a high-end power supply
Safety
- Prevent from higher battery temperature by output voltage and current control
- Maintains low battery temperature during restoring (Input Over - voltage Protection)
- Stable current / Voltage supply (Control input voltage variation function)
- Prevents potential hazard caused by high battery temperature
