Fluke 1587 FC Advanced Electrical Troubleshooting Kit

GENERAL SPECIFICATIONS
Maximum voltage applied to any terminal and common	1000 V
Storage temperature	-40 °C to 60 °C (-40 °F to 140 °F)
Operating temperature	-20 °C to 55 °C (-4 °F to 131 °F)
Temperature coefficient	0.05 x (specified accuracy) per °C for temperatures <18 °C or >28 °C (<64 °F or >82 °F)
Relative humidity	Noncondensing
	0 % to 95 %  10 °C to 30 °C	(50 °F to 86 °F)
	0 % to 75 % 30 °C to 40 °C	(86 °F to 104 °F)
	0 % to 40 %  40 °C to 55 °C	(104 °F to 131 °F)
Vibration	Random, 2 g, 5-500 Hz per MIL-PRF-28800F, Class 2 instrument
Radio frequency communication	2.4 GHz ISM Band
Radio frequency certification	FCC: T68-FBLE, IC: 6627A-FBLE
Electromagnetic compatibility
International IEC 61326-1	Portable Electromagnetic Environment; IEC 61326-2-2 CISPR 11: Group 1, Class A : Group 1: Equipment has intentionally generated and/or uses conductively-coupled radio frequency energy that is necessary for the internal function of the equipment itself. Class A: Equipment is suitable for use in all establishments other than domestic and those directly connected to a low-voltage power supply network that supplies buildings used for domestic purposes. There may be potential difficulties in ensuring electromagnetic compatibility in other environments due to conducted and radiated disturbances. Emissions that exceed the levels required by CISPR 11 can occur when the equipment is connected to a test object. The equipment may not meet the immunity requirements of this standard when test leads and/or test probes are connected.
Korea (KCC)	Class A Equipment (Industrial Broadcasting & Communication Equipment) Class A: Equipment meets requirements for industrial electromagnetic wave equipment and the seller or user should take notice of it. This equipment is intended for use in business environments and not to be used in homes.
USA (FCC)	47 CFR 15 subpart B. This product is considered an exempt device per clause 15.103.
Enclosure protection	IEC 60529: IP40 (non-operating)
Safety	IEC 61010-1	Pollution Degree 2
	IEC 61010-2-033	CAT IV 600 V/CAT III 1000 V
Batteries	Four AA batteries (NEDA 15A or IEC LR6)
Battery life	Meter use 1000 hours; Insulation test use: Meter can perform at least 1000 insulation tests with fresh alkaline batteries at room temperature. These are standard tests of 1000 V into 1 MO with a duty cycle of 5 seconds on and 25 seconds off.
Size	5.0 cm H x 10.0 cm W x 20.3 cm L (1.97 in H x 3.94 in W x 8.00 in L)
Weight	550 g (1.2 lb)
Altitude	Operating	2000 m
	Storage	12,000 m
Over-Range capability	110 % of range except for capacitance which is 100 %
Frequency overload protection	<107 V-Hz
Fuse Protection for mA input	0.44A, 1000 V, IR 10 kA

 

ELECTRICAL SPECIFICATIONS
AC voltage measurement
Accuracy (1587 FC only)
Range	Resolution	50 Hz to 60 Hz ± (% of Rdg + counts)	60 Hz to 5000 Hz ± (% of Rdg + counts)
600.0 mV	0.1 mV	± (1 % + 3)	± (2 % + 3)
6.000 V	0.001 V	± (1 % + 3)	± (2 % + 3)
60.00 V	0.01 V	± (1 % + 3)	± (2 % + 3)
600.0 V	0.1 V	± (1 % + 3)	± (2 % + 3) 1
1000 V	1 V	± (2 % + 3)	± (2 % + 3) 1
1 1 kHz bandwidth
Low-Pass Filter Voltage (1587 FC only)
Range	Resolution	50 Hz to 60 Hz ± (% of Rdg + Counts)	60 Hz to 400 Hz ± (% of Rdg + Counts)
600.0 mV	0.1 mV	± (1 % + 3)	+ (2 % + 3) - (6 % - 3)
6.000 V	0.001 V	± (1 % + 3)	+ (2 % + 3) - (6 % - 3)
60.00 V	0.01 V	± (1 % + 3)	+ (2 % + 3) - (6 % - 3)
600.0 V	0.1 V	± (1 % + 3)	+ (2 % + 3) - (6 % - 3)
1000 V	1 V	± (2 % + 3)	+ (2 % + 3) - (6 % - 3)

 

1577 accuracy
Range		Resolution	50 Hz to 60 Hz ± (% of Rdg + Counts)
600.0 mV		0.1 mV	± (2 % + 3)
6.000 V		0.001 V	± (2 % + 3)
60.00 V		0.01 V	± (2 % + 3)
600.0 V		0.1 V	± (2 % + 3)
1000 V		1 V	± (2 % + 3)
AC Conversion		Inputs are ac coupled true-rms responding and specified from 5 % to 100 % of range. Input signal crest factor can be up to 3 up to 500 V, decreasing linearly to a crest factor =1.5 at 1000 V. For non-sinusoidal waveforms add ± (2 % reading + 2 % FS) typical, for a crest factor up to 3.
Input Impedance		10 MΩ (nominal), <100 pF, ac-coupled
Common mode rejection ratio (1 kΩ unbalanced)		>60 dB at dc, 50 or 60 Hz
DC voltage measurement
Range		Resolution	Accuracy 1587 FC1 ± (% of Rdg + Counts)	Accuracy 15771 ± (% of Rdg + Counts)
6.000 V dc		0.001 V	± (0.09 % + 2)	± (0.2 % + 2)
60.00 V dc		0.01 V	± (0.09 % + 2)	± (0.2 % + 2)
600.0 V dc		0.1 V	± (0.09 % + 2)	± (0.2 % + 2)
1000 V dc		1 V	± (0.09 % + 2)	± (0.2 % + 2)
1 Accuracies apply to ± 100% of range.
Input Impedance: 10 MΩ (nominal), <100 pF
Normal mode rejection ratio: >60 dB  50 Hz or 60 Hz
Common mode rejection ratio: >120 dB  dc, 50 Hz or 60 Hz (1 k unbalanced)
DC millivolts measurement
Range		Resolution	Accuracy 1587 FC ± (% of Rdg + Counts)	Accuracy 1577 ± (% of Rdg + Counts)
600.0 mV dc		0.1 mV	± (0.1 % + 1)	± (0.2 % + 1)
DC and AC current measurement
Range		Resolution	Accuracy 1587 FC ± (% of Rdg+Counts)	Accuracy 1577 ± (% of Rdg+Counts)	Burden voltage (Typical)
AC 45 Hz to 1000 Hz	400 mA	0.1 mA	± (1.5 % + 2) 1	± (2 % + 2) 1	2 mV/mA
	60 mA	0.01 mA	± (1.5 % + 2) 1	± (2 % + 2) 1
DC	400 mA	0.1 mA	± (0.2 % + 2)	± (1.0 % + 2)	2 mV/mA
	60 mA	0.01 mA	± (0.2 % + 2)	± (1.0 % + 2)
1 1 kHz bandwidth
Overload: 600 mA for 2 minutes maximum
Fuse protection for mA Input: 0.44 mA, 1000 V, IR 10 kA
AC conversion: Inputs are ac coupled true-rms responding and specified from 5 % to 100 % of range. Input signal crest factor can be up to 3 up to 300 mA, decreasing linearly to crest factor =1.5 at 600 mA. For non-sinusoidal waveforms add +(2 % reading + 2 % FS) typical, for a crest factor up to 3.
Ohms measurement