Product Description
We supply tungsten wire, tungsten bar, tungsten plate, tungsten sheet, tungsten rod, tungsten electrode, tungsten fabricated parts, tungsten alloy, tungsten copper alloy, tungsten heavy alloy. Please contact with our sales department for more details.
We produces two types of tungsten wire - Pure and WAL (K-Al-Si doped).
Pure tungsten wire is produced in sizes above. 020 inches in diameter. Typical usage is for restraightening into rod products and for applications where there is a low alkali content requirement.
WAL wire which has been doped with trace amounts of potassium, causing the wire to exhibit an elongated interlocking grain structure with non-sag properties after recrystallization. WAL wire is produced in sizes from less than 0.02mm up to 6.5mm in diameter and is used largely for lamp filament and wire filament applications.
Dimensions and Tolerances
Wire diameters are generally expressed in terms of mm(or inches). For thin wires from 0.02mm up to 0.5mm in diameter, the diameter of the wire is measured by weight per unit length. That is, the weight expressed in mg of a 200 mm length of wire.
The standard diameter tolerance is 3% of the weight measurement. Closer tolerances are available, depending upon the application for the wire product.
For thicker wires from 0.5mm up to 6.5mm in diameter, the mm measurements are used. The tolerances are expressed as a percentage of the diameter. Standard tolerance is 1.5%.
Tensile Strength
Tensile strength for tungsten wire is usually expressed in grams per milligram weight of a 200mm (or) g/mg/200mm. The normal range of values is from 40 to 110 grams. In general, as tensile strength increases, wire straightness decreases.
Straightness
Wire may be finished in the unstraightened or as drawn condition and is controlled to FOTMA's internal standards, In addition, wire can be straightened via mechanical or heat treating processes. Typically, the measure of the straightness of a tungsten wire is obtained by cutting a ten inch long piece of wire and allowing it to lie on a flat clean surface. The maximum deviation from a straight line along its length is the quantitative measure of its straightness. In general, as the degree of straightness increases, tensile strength decreases.
Splits
Longitudinal cracks with a depth of more than 15% of the wire diameter are called splits. The wire is checked for splits with an eddy current split detector. The split level for a given length of wire is typically less than 5%.
Quality and Finish
Wire is free of scratches, kinks and distortions insofar as they are harmful to the intended end use of the product. Surface finish is supplied in the black, as drawn condition, where drawing lubricants and oxides are retained on the surface, or in the cleaned condition by firing in hydrogen or electrochemical etching.
Spooling
Wire is spooled on clean, defect free spools. For very large diameters, tungsten wire is self coiled. Spools are level filled without piling near flanges. The outer end of the wire is properly marked and attached securely to the spool or self coil.
| 1. Tungsten Wires |
| Diameter (µm) | Wire Weight per 200mm in length (mg) | Wire Weight per 200mm in length for tolerance (%) |
| 15 d 18 | > 0.3~0.98 | Class A | Class B |
| + 2.5 | + 3.0 |
| 18 < d 40 | >0.98~4.85 | + 2.0 | + 2.5 |
| 40 < d 80 | >4.85~19.39 | + 1.5 | + 2.0 |
| 80 < d 300 | >19.39~30.30 | + 1.0 | + 1.5 |
| 300< d 400 | >272.71~484.80 | + 0.5 | + 1.0 |
| Type | Name | Kind | Applications |
| WAL1 | Nonsag tungsten wires | L | Used in making single coiled filaments, filaments in fluorescent lamps and other components. |
| B | Used in making coiled coil and filaments in High power incandescent bulb, stage decoration lamp, heating filaments, halogen lamp, special lamps etc. |
| T | Used in making special lamps, exposition lamp of copy machine and lamps used in automobiles. |
| WAL2 | Nonsag tungsten wires | J | Used in making filaments in incandescent bulb, fluorescent lamp, heating filaments, spring filaments, grid electrode, gas-discharge lamp, electrode and other electrode tubes parts. |
Product Show
Related products
About Us
Baoji Zhengqian Nonferrous Metals Co. Ltd is located in the nonferrous metal processing base—Baoji City, Shaanxi Province, China. Our company is a comprehensive enterprise, and we have integrated the processing production and developing sales of the refractory metal and non-ferrous metal materials.Advanced production technology and modern production equipment have been applied to professionally manufacture tungsten, molybdenum, tantalum, titanium, nickel and their alloyed materials and exquisite-manufactured parts , such as sheet, bar, pipe, foil, wire, target and crucible in various specifications. Our productions are widely used in many fields, for instance, aircraft industry, petrochemical industry, metallurgy, rare earth, coating, instrumentation, LED, electronic equipment, solar PV and medical equipment.We have been insisted on “quality first, reputation first and faith first” for our business philosophy. And we have been providing better and better productions and service for our customers with all our hearts to get win-win cooperation and seek bilateral development.
Contact
