Stroke Switch Wholesale

DDTG-55Z High Speed Tubular Linear Actuator

• Min. Order:  

  3000 Piece

• Price:  

  CNY 200 ~ 2000

• Place of origin:  

  China

Stroke Length 50～500mm Motor Type brushed motor Max Load 400N (24V) / 250N(12V) Load Speed 80-90mm/s Limit Switch built-in Duty Cycle under max load,work for 50 times , stop for 20minutes（15%-20%）;under min load can work continuously Protection Class IP67 Operating temperature -20-60ºC Wire length Custom Noise on load ≤60db Dimension of DDTG-55Z High Speed Tubular Linear Actuator DDTG-55

[Related Keywords : high speed electric linea]

AG-26 Magnetic Cylinder Sensor

• Min. Order:  

  50 Box

• Price:  

  US$ 100

• Place of origin:  

  China

Switching Logic Normally Open Solid State Output, Normally Open Output Type 2 Wire Solid State NPN Current Sinking PNP Current Sinking voltage Range 10～30V DC 5～30V DC Sensor Current 1～50 mA 0～100 mA Switch Rating 1.5 W Max. 3W Max. Consumption / Voltage Drop Leakage Current 0.01 mA Max. Indicator Red LED Red LED Green LED Cable Φ2.2, 2C, Grey Oil-Resistant PUR Φ2.2, 3C, Grey Oil-Resist

[Related Keywords : sensor cylinder]

High Pressure Pipe Crimping Machine

• Place of origin:  

  China

stroke switch during the first withholding process until the diameter of the jacket meets the requirements after withholding. And some compression quality is difficult to guarantee. Due to the lack of theoretical research on the amount of compression in the hose assembly, no definite adjustment amount can be given when the hose assembly is inconsistent with the standard assembly.The critical seal

[Related Keywords : Pipe Crimping Machine]

C Type Punch Press Machine

• Place of origin:  

  China

switch Electric Slide adjust device(APA 60 above) Quick die change device(die lifter, clamp and die arm) Mechanical Die height indicator( APA below 60) Slide knock-out device Electric Die height indicator(APA 60 below) Die room light Balance device Photo-electronic safety device Crank angle indicator Feeder Electric stroke counter Uncoiler Air source receptacle Straightener Against over-run safet

[Related Keywords : Press Machine]

WJ-PFP510A

Features This machine is a hydraulic panel punching press that has been patented first in Korea and has been designed with the special emphasis on safety. The machine is capable of processing a stainless plate used for switch boards and s steel plate used for fire proof door. The operator can move the boards forth/back and left/right easily to process materials. In addition, the machine can

[Related Keywords : Panel Punching Press]

GI Custom Roll Forming Machine 5.5KW Recoiling Line and Perforation Line

• Place of origin:  

  China

stroke of coil carMax300mmForward/Backward stroke of coil carMax. 1000mmStop/start rotationAutomatic stopping device with limited switch to assist PLC Control SystemFunctionControl the perforation automaticallyPLCSiemensTouch screenSiemensInverterSchneider or DeltaEncoderOmronPunching tolerance≤±1 mmControl Voltage24V Support and Services:Technical Support and Service for Our Machines We provi

[Related Keywords : Custom Roll Forming Machi]

Motor Housing Induction Heater Motor Frame Casing Profile Enclosure Motor Shell Cover Heater Stator

• Min. Order:  

  1 Set

• Price:  

  USD 1500

• Place of origin:  

  China

• Price Condition:  

  FOB Negotiable

• Supply Ability:  

  1000sets/month

switched off thus saving energy. (Published by Tony,mail: tudishen#126 dot com) Energy efficiency - Due to the heat being generated within the component energy transfer is extremely efficient. the induction heater heats only the part not the atmosphere around it. Process consistency - the induction heating process produces extremely uniform consistent heat this often allows less heat to be used

[Related Keywords : die-casting motor case, assembly, interference fit, motor stator assembly]

Motor Housing Induction Heater Motor Frame Casing Motor Profile Shell Heater Assembly Shrink Fitting

• Min. Order:  

  1 Set

• Price:  

  USD 999

• Place of origin:  

  China

• Price Condition:  

  FOB Negotiable

• Supply Ability:  

  1000sets/month

switched off thus saving energy. (Published by Tony,mail: tudishen#126 dot com) Energy efficiency - Due to the heat being generated within the component energy transfer is extremely efficient. the induction heater heats only the part not the atmosphere around it. Process consistency - the induction heating process produces extremely uniform consistent heat this often allows less heat to be used

[Related Keywords : aluminium motor enclosure heater, interference fit mounting, motor stator rotor dismounting, blind hole through hole]

1200mm CNC Drilling Milling Machine with Low Price

• Min. Order:  

  1

• Place of origin:  

  China

• Price Condition:  

  FOB Qindgao

• Supply Ability:  

  80 sets per month

stroke 1200mm*300mm*280mm Power supply 380V 50Hz or As Customer need Max rotary speed 18000RPM Main spindle Power 3KW Handle type ER25*Φ8 Processing range 100*140mm Overall size 2200×1500×1950mm Weight 610kg Main accessory Control system Taiwan Syntec Solenoid valve Germany FESTO Cylinder PC(FESTO Joint Venture Brand) Motor Anhui Sanyang (Best Chinese Motor Brand) Air Filter Devic

[Related Keywords : drilling milling machine, aluminum machine, window door machine, aluminum processing machine]

Supercombinata SC1

• Min. Order:  

  1

• Place of origin:  

  Italy

• Price Condition:  

  FOB

STROKE Unlimited: With 350 mm pitch ELECTRONIC CONTROL PANEL Voltage: 220/240 V (50/60 Hz) Main switch: Available Emergency switch: Available Inverter feed: RH/LH Inverter rotation: CW/CCW Speed regulator: Rotation/Feed Electrical absorption: 2000 W Control panel 110/120 V: Upon request Digital control panel: Upon request DIMENSIONS Length: 680 mm Width: 240 mm Height: 380 mm Weight central unit:

[Related Keywords : Line boring, Overlay welding, Flange facing, Threading]

Larg Semi-automatic Grinding Machine

• Min. Order:  

  1 Set

• Price:  

  US$ 11500 ~ 13500

• Place of origin:  

  China

• Supply Ability:  

  100

The front and side of the diamond saw blade are semi-automatically grinding. Main features 1.Saw blade three-sided cutting function 2.Manual control of grinding wheel feed 3.Variable speed motor with main body speed adjustment 4.It can automatically adjust the stroke in the vertical direction within the range of 10~50mm - 5.Use the potentiometer on the main switch board to adjust the sliding spee

[Related Keywords : saw blade, grinding machine, grinding, segments]